2016 J BOATS J 95

Hall Spars tapered Carbon mast, with double airfoil spreaders, main, jib and spinnaker halyard sheaves, Harken Type A mast track Asy Spinnaker Package Mast finished in White Awlgrip G10 fiberglass mast step with fore/aft adjustment slots and SS padeye for through bolt securing of mast to step Mast Wedge Aluminum boom with provision for 2 reefs, 8:1 internal mainsail outhaul in Awlgrip off-white Continuous rod rigging with adjustable shroud turnbuckles Running rigging package with main halyard, jib halyard, two jib sheets, main sheet, single line reef, traveler control lines, and centerboard pennant and control line NavTech hydraulic backstay adjuster Rigid boomvang with purchase Harken MK IV Unit 0 headsail furler with control leading aft through 2 fairleads to Harken 150 cam cleat mounted on port cabin side Bowsprit package with internal fiberglass sprit tube installed with flush cover Optional asymmetric spinnaker gear package installed including carbon sprit, bearings, retrieval purchase, blocks and running rigging and snuffer system

Moondust Two Tone Deck Low maintenance custom stainless handrails on cabin house (2) Harken 40.2STA 2 speed self-tailing winches mounted on cockpit coamings (2) Harken 32.2A, 2 speed self-tailing winches mounted beside companionway Triple Harken deck organizers Harken Adjustable Genoa Track System 6 Harken mast collar turning blocks Spinlock XTS triple rope clutches Floor mounted Harken mainsheet traveler track with 4:1 Harken traveler control system leading to cockpit vertical wall to Harken 150 cam cleats 5:1 Harken mainsheet system leading to Harken 144 swivel cam base on a custom SS riser mounted on centerline aft of the traveler 10:1 fine tune adjustment system Interior ventilation from two framed BSI Moonlight opening ports in sides of cabin trunk and offshore style forward skylight deck hatch above V-berth. Optional two aft facing opening ports installed Companionway opening with SS covered PVC slider tracks, large gutter drains, molded seahood with sliding cover Acrylic offshore removable dropboard in aluminum frame with inside/outside lockable hasp Cockpit operated manual bilge pump operable from the helm position with SS transom exhaust fitting Two polypropylene mesh line bags for halyard and sheet line tail storage Custom designed and fabricated SS chainplates, stemhead and backstay fittings Four (4) folding padeyes for attachment points of spinnaker blocks Custom SS bow and stern rails with Perko integral navigation lights SS removable stanchions with double lifelines PandS and at transom Custom SS Pedestal Guard Option Installed Opening Ports in Aft Face of Cabin Option Installed

Off White main bulkhead with varnished teak trim, teak oval door opening with white door Teak and holly synthetic high-wear cabin sole in main cabin and head Teak trimmed storage bins outboard of each settee berth seat back Raritan PH-II marine head with 14 gal holding tank and "Y" valve Molded sink with overboard drain in head Settee cushions with piping Vinyl liner finish on main cabin and head overhead and main cabin hull sides. Air dry gelcoat finish on hull sides in head and V-berth area and aft storage lockers Manual Fresh Water System

2 Cylinder 14 HP Yanmar engine with saildrive and 15" Flex-O-Fold geared folding propeller Yanmar engine instrument panel with tachometer, engine hour gauge and water, oil pressure alarms and separate fuel gauge in cockpit with acrylic splash cover Engine throttle control with neutral safety switch Waterlock muffler with exhaust run aft to SS transom exhaust fitting 15 gal fuel tank with baffles and inspection port Balanced twin rudder system with self-aligning JP-3 rudder bearings and rudder shafts Edson steering components including bulkhead steerer, radial drive, tiller arm, link bar, articulock idler sheaves and wire chain assembly 44" leather covered Edson destroyer wheel mounted on custom molded steering pedestal Ritchie binnacle mounted compass and custom fabricated SS wheel guard/handhold